 |  |  |  |  |  |
 |  |  |  |  |  |
| Frame Services |
| Slide Services |
| Some slide services will require the slide to be refinished. Refinish work can be done in black, OD green,Flat Dark Earth,Silver or gray. This finish is very rust resistant. It will show holster wear and if barrel is finished, will wear on bearing surfaces as will the inside of the slide. If finish flakes off due to a coating fault, it will be reapplied at no cost. Refinishing Glock slides with old staked plastic factory sights requires that the sights be replaced sights of the customer's choosing. |
Slide refinish Ceramic 90.00 Slide refinish Melonite Black only 100.00
Slide, levers and barrel 100.00 Slide and levers Melonite 115.00
Sand blast stainless slide 20.00
Radius slide (remove sharp edges)- SA-XD, H&K, Kimber 35.00 Mill slide
-Glock and Kahr 20.00 to accept
Contour front and rear of slide and ejection port. Great for concealment! 110.00 J-point or
Slide contouring for guns with front factory contour (Glock) 55.00 or trijicon
Forward cocking serrations 90.00 Red Dot
Supply and install XS night sights 110.00 $175.00
Supply and install AmeriGlo Glock night sights 90.00
Steel replacement Glock sight (3 dot non-tritium) 30.00
Slide, levers and barrel 100.00 Slide and levers Melonite 115.00
Sand blast stainless slide 20.00
Radius slide (remove sharp edges)- SA-XD, H&K, Kimber 35.00 Mill slide
-Glock and Kahr 20.00 to accept
Contour front and rear of slide and ejection port. Great for concealment! 110.00 J-point or
Slide contouring for guns with front factory contour (Glock) 55.00 or trijicon
Forward cocking serrations 90.00 Red Dot
Supply and install XS night sights 110.00 $175.00
Supply and install AmeriGlo Glock night sights 90.00
Steel replacement Glock sight (3 dot non-tritium) 30.00
| The Inside Stuff |
Polish chamber and feed ramp (reliability) 25.00
Supply and fit 3.5 or 5 lb. GHOST connector with trigger job 80.00
Trigger job without new connector 60.00
Trigger job for SA-XD and H&K 85.00
Full trigger w/ reduced pre and over travel XD 140.00
Supply and fit 3.5 or 5 lb. GHOST connector with trigger job 80.00
Trigger job without new connector 60.00
Trigger job for SA-XD and H&K 85.00
Full trigger w/ reduced pre and over travel XD 140.00
| Shipping and Payment Instructions |
-Due to shipping regulations, all firearms are to be shipped via UPS or Fed Ex Next Day
Air.
-The customer is responsible for insuring their own shipment to Bowie Tactical Concepts.
-Bowie Tactical Concepts will insure the firearm for return shipment.
-All firearms shipped must include a letter containing the work required by the customer along
with a phone number and customer address for return shipment or print and fill out our order
form (click here for printable order form).
-Bowie Tactical Concepts will accept payment in the form of Mastercard, Visa, personal check,
money order, or cashier's check. add 3% for CC RESIDENTS OF OHIO PLEASE ADD
7% SALES TAX. MAKE CHECKS PAYABLE TO BOWIE TACTICAL CONCEPTS.
-Return shipment will be billed with return of your firearm. If paying by credit card, shipping will
be billed to your credit card on return shipment.
-BTC return ships via UPS only and will use UPS Next Day
Air Saver where available. Slides only will be USPS priority.
-Usual time for complete work and return of your firearm is
around
16 to 24 weeks, depending on demand and work
requested. Can be longer
SERVICES WILL BE ADDED AS DEMAND REQUIRES. IF YOU DON'T SEE WHAT YOU NEED, ASK. ALL WORK
IS HAND PERFORMED SO IT CAN BE TAILORED TO YOUR NEEDS.
PRICES ARE EFFECTIVE AS OF 9/1/10 AND ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Bowie Tactical Concepts
124 Roy Pence Road
West Union, Ohio 45693
(937)544-4606
Air.
-The customer is responsible for insuring their own shipment to Bowie Tactical Concepts.
-Bowie Tactical Concepts will insure the firearm for return shipment.
-All firearms shipped must include a letter containing the work required by the customer along
with a phone number and customer address for return shipment or print and fill out our order
form (click here for printable order form).
-Bowie Tactical Concepts will accept payment in the form of Mastercard, Visa, personal check,
money order, or cashier's check. add 3% for CC RESIDENTS OF OHIO PLEASE ADD
7% SALES TAX. MAKE CHECKS PAYABLE TO BOWIE TACTICAL CONCEPTS.
-Return shipment will be billed with return of your firearm. If paying by credit card, shipping will
be billed to your credit card on return shipment.
-BTC return ships via UPS only and will use UPS Next Day
Air Saver where available. Slides only will be USPS priority.
-Usual time for complete work and return of your firearm is
around
16 to 24 weeks, depending on demand and work
requested. Can be longer
SERVICES WILL BE ADDED AS DEMAND REQUIRES. IF YOU DON'T SEE WHAT YOU NEED, ASK. ALL WORK
IS HAND PERFORMED SO IT CAN BE TAILORED TO YOUR NEEDS.
PRICES ARE EFFECTIVE AS OF 9/1/10 AND ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Bowie Tactical Concepts
124 Roy Pence Road
West Union, Ohio 45693
(937)544-4606
Glock grip reduction (includes 360 stippling) 195.00
Glock and SA-XD beaver tail 175.00
Stipple grip full 360 degrees removing existing checkering 100.00
Stipple front and back removing existing checkering 80.00
Stipple front strap 30.00
Remove finger grooves and stipple front strap (Glock) 55.00
Remove finger grooves as part of other stippling pkg. 25.00
Stipple under trigger guard (full or partial) 15.00
Stipple thumb rest (forward thumb) Glock, Kahr, Kimber 15.00
SA-XD (only right side area) 10.00
Round front of trigger guard (requires stippling included in price) 40.00
Magazine well cut outs 20.00
Remove angle cuts in magazine well and fully open 20.00
Cut rear of grip tang down to slide and radius (SA-XD) 45.00
Cut down slide stop (Glock, SA-XD, Kahr)
-Refinish required on blued parts, ask 20.00
Radius take down lever (SA-XD) -Refinish required, ask 20.00
Short Grip "SG" modification (ex. Glock 17 cut down to 19 mags) 70.00
Crimson Trace Grip stippling (customer supplied CTC grip)-Glock unit 50.00
-M&P unit 30.00
Mag release button scallop 10.00
Round extended magazine release button 35.00
Rear trigger guard radius, IE undercut 15.00
Glock and SA-XD beaver tail 175.00
Stipple grip full 360 degrees removing existing checkering 100.00
Stipple front and back removing existing checkering 80.00
Stipple front strap 30.00
Remove finger grooves and stipple front strap (Glock) 55.00
Remove finger grooves as part of other stippling pkg. 25.00
Stipple under trigger guard (full or partial) 15.00
Stipple thumb rest (forward thumb) Glock, Kahr, Kimber 15.00
SA-XD (only right side area) 10.00
Round front of trigger guard (requires stippling included in price) 40.00
Magazine well cut outs 20.00
Remove angle cuts in magazine well and fully open 20.00
Cut rear of grip tang down to slide and radius (SA-XD) 45.00
Cut down slide stop (Glock, SA-XD, Kahr)
-Refinish required on blued parts, ask 20.00
Radius take down lever (SA-XD) -Refinish required, ask 20.00
Short Grip "SG" modification (ex. Glock 17 cut down to 19 mags) 70.00
Crimson Trace Grip stippling (customer supplied CTC grip)-Glock unit 50.00
-M&P unit 30.00
Mag release button scallop 10.00
Round extended magazine release button 35.00
Rear trigger guard radius, IE undercut 15.00
| The BTC S&W M&P |
| Glock CTC Grip without stippling-200.00 Glock CTC Grip with stippling- 245.00 S&W M&P CTC Grip without stippling-265.00 S&W M&P CTC Grip with stippling-295.00 (Specify Glock Model when ordering Glock unit) Available in our Guns and Gear Store |
| KA/BAR-TDI Concealed Carry Fanny Packs $32.50 each |
| TDI Law Enforcement Knives |
Milling for red
dots including
RMR, J-point,
Deltapoint and
MRDS is $175 the
RMR and
DELTApoint can
also be done with
dovetail cut for
$50 and additional
suppressor sights
for $55 this is a
great BUIS set up
and has become
the new industry
buzz.
dots including
RMR, J-point,
Deltapoint and
MRDS is $175 the
RMR and
DELTApoint can
also be done with
dovetail cut for
$50 and additional
suppressor sights
for $55 this is a
great BUIS set up
and has become
the new industry
buzz.
ADD 3% for
credit card
credit card